ZBoost YX645 Specifications Page 2
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
For questions or assistance, contact zBoost customer service at 1-800-871-1612
or email [email protected]
LIMITED 1 YEAR WARRANTY | REGISTER AT WWW.ZBOOST.COM
zBoost warrants every zBoost product to be free from defects in material and workmanship under normal use for the warranty period of 1 year.
Who Is Covered?
You must have proof of purchase to receive warranty service. A sales receipt or other documentation showing the product purchased and the
purchase date is considered proof of purchase. This limited warranty extends only to the original consumer purchaser or any person receiving
the product as a gift from the original consumer purchaser and to no other purchaser or transferee. This warranty does NOT extend to
commercial users.
What is Covered?
Warranty coverage begins the day you purchase the product. For one year from the original date, the zBoost Cell Phone Signal Booster will be
repaired or replaced with a new, repaired, refurbished or comparable product (whichever is deemed necessary by zBoost) if it becomes
defective or inoperative. The exchange will be made without charge to you for parts and labor. You will be responsible for the cost of shipping
to the location designated by zBoost. If zBoost cannot reasonably repair or replace the unit then zBoost may, at its sole discretion, refund the
price you paid for the product. All products, including replacement products, are covered only for the original warranty period. When the
warranty on the original product expires, the warranty on the replacement product also expires.
What is Excluded?
Your warranty does NOT cover:
• Labor charges for set up of the unit.
• Product replacement because of misuse, accident, lightning damage, unauthorized repair or other cause not within the control of zBoost.
• Incidental or consequential damages resulting from the product. Some states do not allow the exclusion of incidental or consequential
damages, so the above exclusion may not apply to you.
• Any modications or other changes to the product, including but not limited to software or hardware modications in any way other
than as expressly authorized by zBoost will void this limited warranty.
• Product that has been modied or adapted to enable it to operate in any country other than the country for which it was designed,
manufactured, approved and/or authorized, or repair of products damaged by these modications.
Make sure you keep…
Please keep your sales receipt or other document showing proof of purchase. Attach it to this Setup Overview and keep both nearby. Also,
keep the original box and packing material in case you need to return your product.
Before requesting repair service…
Please review the BASE UNIT LED INDICATORS section listed in this overview - This may save you a call.
To get warranty service…
Warranty service will be provided by zBoost. If you believe you need service for your unit, contact zBoost
at 1-800-871-1612 or
[email protected]. A representative will go through a diagnostic checklist with you. If it is determined that the product needs to be
returned for service or exchanged, you will receive a return merchandise authorization (RMA) number. The representative will give you
complete shipping details. Do not return products to zBoost without a Return Authorization Number (RMA).
To get out of warranty service…
To obtain out of warranty service, contact zBoost at 1-800-871-1612 or [email protected] for information on the possibility of any costs for
repair or replacement of out-of-warranty products.
Reminder: Record the model and serial number found on the product below:
Model #:
Serial #:
Purchase Date:
WARRANTY INFORMATION
CUSTOMER SERVICE
FCC Information
FCC ID: SO4YX545-PCS-CEL
Warning: Changes or modications to this device not expressly approved by zBoost could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency elds, the radiating element
(antenna) shall be installed such that a minimum separation distance of 20cm (8in) is maintained from all persons.
Industry Canada Regulations
Canada IC: 5544A-YX545PCSCEL
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
The term “IC:” before the radio certication number only signies that Industry Canada technical specications were met.
RF Exposure:
The manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would
have to be reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means
of input power or gain reduction and not by an attenuator at the output of the device.
Please note: This unit has been approved for use in Canada under RSS 131, however, consent for the use of this device to improve cellular or PCS coverage, must be
obtained through your cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry Canada document CPC 2-1-05, Section 6.1 available
or viewable at: http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html
Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette
aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y
compris l’interférence qui peut causer l’opération peu désirée.
Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les situations lorsque plusieurs signaux porteurs sont présents,
l’évaluation devrait être réduite de 3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des interférences adjacentes à la bande
utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie d’alimentation ou la réduction de gain et non par un atténuateur à la sortie du dispositif.
The zBoost YX645 User Guide and additional product information is
available at www.zBoost.com
YX645 Technical Specications
PCS Frequency CEL Frequency
Frequency 1850 - 1990 MHz 824 - 894 MHz
System Gain 75 dB 67 dB
Band Supported ALL: A,D,B,E,F & C ALL: A,B, A’ & B’
Antenna Signal 13 dBi Panel; F-type female 8 dBi Panel; F-type female
Antenna- Base Unit 9 dBi Panel; TNC male 6 dBi Panel; TNC male
Cable Loss
3000 MHz RG-6, approx. 1 dB/10 ft. 3000 MHz RG-6, approx. 0.6 dB/10 ft.
Both PCS and CEL Frequencies
Network Format CDMA, GSM, TDMA, AMPS, GPRS, EDGE, EVDO, HSPA, 3G
Base Unit RF Connectors F-type female and TNC female
Wall Supply Unit 100-240 VAC 50 Hz-60Hz
System Certifications
Power Consumption 3W standby; 7W max signal - 2.0A Max
UL, FCC Parts 15 & 24 (PCS), FCC Parts 15 & 22 (CEL), Industry Canada
Base Unit Size and Weight 5” x 7” x 1.375” - 12 oz.
Base Unit and Power Supply Indoor Use Only, 5° to 40° C (40° to 105° F)
Coverage (open areas) 4-5 signal bars at the roof antenna; 110’ radius at 100° width;
3-4 signal bars inside; over 10,000 sq. ft.
Handles all PCS or CEL protocols and included multiple patented and patent pending technologies to provide low-
cost coverage while continually adapting to signal to prevent interference and remain transparent to the wireless
network. Provides an indicator if the antennas are positioned improperly, but will NOT suffer damage of interfere
with the Carrier Network.
You can also download the User Guide at www.zBoost.com/customersupport
1
2
Related products and manuals for Cellular signal boosters ZBoost YX645
(23 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals